Lift kit for Lincoln MKZ - Second generation | CD533 | 2012-2020

Lift set for Lincoln MKZ - Second Generation (2012-2020) | Classic Series

Restore lost ride height and upgrade the everyday capability of your second-generation Lincoln MKZ (CD533, 2012–2020). Over time, factory suspension springs naturally sag under the weight of this heavy luxury sedan, leaving its sleek, low front end and exhaust system vulnerable. Installing this polyurethane lift kit compensates for sagging springs and adds essential ground clearance, allowing you to easily navigate deep winter snow, clear steep parking ramps, and park near high city curbs without scraping. It significantly improves rough-road confidence and urban practicality while keeping your exact factory suspension settings and smooth, quiet ride comfort completely unchanged.

• Front strut spacers | 30 mm (1.2") — 2 pcs.
• Rear coil spacers | 30 mm (1.2") — 2 pcs.
• Rear shock extenders | 28 mm (1.1") — 2 pcs.
• Front Reinforced bolts | M8 extended — 6 pcs.
• Thread locker | Medium strength (Blue) — 1 pc.

• Front: +30mm lift (30mm spacers)
• Rear: +30mm lift (30mm spacers)

📏 Looking for a different height?
Check the "Other Size Options" section at the bottom of this page for available spacer heights and custom configurations.

This complete lift kit is engineered for:

Years: 2012, 2013, 2014, 2015, 2016, 2017, 2018, 2019, 2020

☑️ Full Compatibility: This lift kit is 100% compatible with all second-generation Lincoln MKZ (CD533) model variants across all production years (both Pre-facelift and Facelift versions). It seamlessly fits all factory trim levels (Premiere, Select, Reserve, Black Label), both drivetrain configurations (Front-Wheel Drive and Intelligent All-Wheel Drive), and all powertrain options (including 2.0L EcoBoost, 3.7L V6, 3.0L Twin-Turbo V6, and 2.0L Hybrid variants) produced from 11.2012–07.2020.

⚠️ CCD Suspension Notice: Most second-generation Lincoln MKZ models are factory-equipped with Lincoln Drive Control featuring CCD (Continuously Controlled Damping) adaptive suspension. While this lift kit is physically 100% compatible with CCD dampers, it requires mandatory mechanical height sensor adjustment and electronic Zero Point Calibration using a diagnostic scanner (such as FORScan or Ford IDS) post-installation. If you or your workshop are not prepared to perform these complex suspension sensor configurations, this lift kit is NOT recommended for your vehicle. Skipping this step will lead to incorrect adaptive damping behavior, harsh ride quality, and chassis control system errors.

• Front Axle Installation (Bolts): To accommodate the lift spacers, the original factory bolts in the front upper strut mounts must be replaced with the high-tensile extended bolts included in the kit. These bolts thread directly into the body mounting points to ensure a secure and rigid connection.
• Rear Shock Extenders: Included 28mm steel extenders are required for the +30mm lift to compensate for the suspension travel and restore factory damping range. They ensure the shocks operate within their intended stroke. A thread locker is included in the kit and must be applied to the extender threads to ensure a secure, vibration-resistant fit. Note: These extensions must be installed only if the rear axle lift is 30 mm or more.
• Note on Rear Spacer Design: To achieve the stated +30mm of actual lift, the physical height of the rear spacers is calculated to include the height of the original factory spring pads. By integrating these measurements, we ensure a precise fit and the exact lift height promised, regardless of the thickness of your old, worn-out factory isolators.
• Installation Note (Rear Axle): Important: The factory rubber spring isolators (gaskets) must be removed before installing the new spacers. Our spacers are designed to replace the factory isolators entirely, not to be installed on top of them.
• Lift Height Disclaimer: Please note that the final achieved lift height may vary depending on the individual condition and service life of your vehicle's suspension. Factors such as factory spring fatigue, engine and powertrain weight configurations (standard 2.0L EcoBoost vs. heavy 3.7L/3.0L V6 AWD drivetrains and Hybrid battery systems), panoramic glass roof options (Retractable Panoramic Roof), and heavy optional equipment can influence the final suspension height.

Our spacers are manufactured from professional-grade Polyurethane SCU-PFL-100 (93A Shore hardness). This material is the core of our Classic line, offering distinct advantages:

• Comfort & Quiet:

  Unlike metal spacers, polyurethane effectively absorbs road vibrations, maintaining high ride comfort and reducing suspension noise.

• Stealth Appearance:

  ⚫ The solid classic black color of the polyurethane ensures that the spacers remain invisible under the wheel arches and look like original equipment.

• Extreme Durability:

  100% resistant to road salt, oils, and harsh weather conditions. Polyurethane never rusts or corrodes, making it ideal for both snowy regions and coastal areas with high humidity.

• Structural Integrity:

  The 93A hardness ensures the spacers hold their shape even under heavy loads, while remaining flexible enough to protect your suspension.

• Wheel Alignment: A professional wheel alignment is required after installing the lift kit. This is a mandatory step to ensure proper handling and to keep your tires wearing evenly.
• Self-Installation: A spring compressor is required for installation. Please ensure you have the proper tools if you plan to install the kit yourself.
• Professional Installation: For your safety and the best results, we recommend having this kit installed by a qualified mechanic or a suspension specialist.

While this kit is for +30mm, we offer various heights of spacers to help you build the perfect lift kit for your needs. You can combine different heights to compensate for rear-end sag or to achieve a specific custom stance for your vehicle.

Please contact us to place a custom order. We will help you select the perfect height for your vehicle and provide a custom quote for your personalized setup.

Looking for a different version? We have lift kits for other generations of the Lincoln MKZ:

• ◀️ Previous: Lincoln MKZ - First generation [CD378] (2006-2012)