Lift kit for Lincoln MKT - First generation | Facelift | 2012-2019

Lift set for Lincoln MKT - First generation, Facelift (2012-2019) | Classic Series

Keep your facelift Lincoln MKT (2012–2019) from bottoming out on steep ramps and uneven roads. With its massive three-meter wheelbase and long body overhangs, this luxury crossover is highly prone to scraping its belly and exhaust system, especially when fully loaded with passengers. Installing this polyurethane lift kit raises your ride height just enough to clear speed bumps and high curbs comfortably. It solves the clearance issue without changing how your vehicle drives or sacrificing its smooth, soft factory ride.

• Front strut spacers | 30 mm (1.2") — 2 pcs.
• Rear coil spacers | 30 mm (1.2") — 2 pcs.
• Front Reinforced studs | M10 extended — 8 pcs.
• Additional fasteners | Mounting set — 1 set.

• Front: +30mm lift (30mm spacers)
• Rear: +30mm lift (30mm spacers)

📏 Looking for a different height?
Check the "Other Size Options" section at the bottom of this page for available spacer heights and custom configurations.

This complete lift kit is specifically engineered for:

*FL = Facelift / Restyling

Years: 2012, 2013, 2014, 2015, 2016, 2017, 2018, 2019

☑️ Full Compatibility: This lift kit is 100% compatible with both facelift updates of the first-generation Lincoln MKT model variants. It seamlessly fits all factory trim levels, both drivetrain configurations (Front-Wheel Drive and All-Wheel Drive), and all powertrain options produced from 03.2012–10.2019

⚠️ CCD Notice: Certain configurations are factory-equipped with the CCD (Continuously Controlled Damping) adaptive suspension system. While this lift kit is physically 100% compatible with CCD dampers, it requires mandatory mechanical sensor adjustment and electronic calibration post-installation. If you or your workshop are not prepared to perform these complex suspension sensor configurations, this lift kit is NOT recommended for your vehicle. Skipping this step will lead to setup difficulties, incorrect adaptive damping stiffness, and chassis control system errors.

⚠️ Pre-Facelift Notice: This lift kit is designed exclusively for Facelift models. If your vehicle is an early pre-facelift model (07.2009–02.2012), this kit will not fit because the platform underwent structural updates and the front strut spacers are completely different. The correct kit for your vehicle is in stock — please use product:

• Lift kit for Lincoln MKT - First generation | Pre-Facelift | 2009-2012

• Front Axle Installation (Studs): This kit requires pressing out the original factory splined studs from the front upper strut mounts. They must be replaced with the provided reinforced extended studs to ensure sufficient thread engagement and maximum structural integrity.
• Note on Rear Spacer Design: To achieve the stated +30mm of actual lift, the physical thickness of the rear spacers is calculated to include the height of the original factory spring pads. By integrating these measurements, we ensure a precise fit and the exact lift height promised, regardless of the thickness of your old, worn-out factory isolators.
• Installation Note (Rear Axle): Important: The factory rubber spring isolators (gaskets) must be removed before installing the new spacers. Our spacers are designed to replace the factory isolators entirely, not to be installed on top of them.
• Lift Height Disclaimer: Please note that the final achieved lift height may vary depending on the individual condition and service life of your vehicle's suspension. Factors such as factory spring fatigue, engine weight configurations (standard 3.7L Duratec V6 vs. the significantly heavier 3.5L EcoBoost Twin-Turbo V6 AWD drivetrain), and the presence of heavy optional equipment can influence the final suspension height.

Our spacers are manufactured from professional-grade Polyurethane SCU-PFL-100 (93A Shore hardness). This material is the core of our Classic line, offering distinct advantages:

• Comfort & Quiet:

  Unlike metal spacers, polyurethane effectively absorbs road vibrations, maintaining high ride comfort and reducing suspension noise.

• Stealth Appearance:

  ⚫ The solid classic black color of the polyurethane ensures that the spacers remain invisible under the wheel arches and look like original equipment.

• Extreme Durability:

  100% resistant to road salt, oils, and harsh weather conditions. Polyurethane never rusts or corrodes, making it ideal for both snowy regions and coastal areas with high humidity.

• Structural Integrity:

  The 93A hardness ensures the spacers hold their shape even under heavy loads, while remaining flexible enough to protect your suspension.

• Wheel Alignment: A professional wheel alignment is required after installing the lift kit. This is a mandatory step to ensure proper handling and to keep your tires wearing evenly.
• Self-Installation: A spring compressor is required for installation. Please ensure you have the proper tools if you plan to install the kit yourself.
• Professional Installation: For your safety and the best results, we recommend having this kit installed by a qualified mechanic or a suspension specialist.

While this kit is for +30mm, we offer various heights of spacers to help you build the perfect lift kit for your needs. You can combine different heights to compensate for rear-end sag or to achieve a specific custom stance for your vehicle.

Please contact us to place a custom order. We will help you select the perfect height for your vehicle and provide a custom quote for your personalized setup.